icon ISO 9001 · ISO 13485 · IATF 16949 · ISO 14001 certified manufacturer

Products

Explore products in this family. Open a product for details, or send us your drawing for a custom build.

Part number Description
LF2OX

PATCHCORD 1/4" ORANGE 2FT

TT8RX

PATCHCORD SGL 3COND RED 8FT

LF2PX

PATCHCORD 1/4" PURPLE 2FT

LF6RX

PATCHCORD 1/4" RED 6FT

LF2BLX

PATCHCORD 1/4" BLUE 2FT

LF1OX

PATCHCORD 1/4" ORANGE 1FT

LF3OX

PATCHCORD 1/4" ORANGE 3FT

05AU05

CABLE 1/4" MONO MALE-MALE 25FT

AK243-10

CABLE 3.5MM STER-2RCA MALE 10M

TT8YX

PATCHCORD SGL 3COND YELLOW 8FT

25FN82X

CBL ASSEMBLY RCA JACK(2)-PLUG(2)

LF2GYX

PATCHCORD 1/4" GRAY 2FT

LF2YX

PATCHCORD 1/4" YELLOW 2FT

LF1GNX

PATCHCORD 1/4" GREEN 1FT

TT7BKX

PATCHCORD SGL 3COND BLACK 7FT

TT163X

PATCHCORD TWIN 3-COND 1.5FT

TT5GYX

PATCHCORD SGL 3COND GRAY 5FT

TT8OX

PATCHCORD SGL 3COND ORANGE 8FT

TT4YX

PATCHCORD SGL 3COND YELLOW 4FT

LF1BKX

PATCHCORD 1/4" BLACK 1FT

LF3BK

PATCHCORD 1/4" BLACK 10FT

LF2GN

PATCHCORD 1/4" GREEN 2FT

TT161X

PATCHCORD TWIN 3-COND 0.5FT

TT8BKX

PATCHCORD SGL 3COND BLACK 8FT

About Barrel - Audio Cables

Audio Cable Assemblies includes mono, stereo and four-conductor audio leads, extension cables and patch cords.

When selecting an assembly, check connector diameter, plug or jack arrangement, contact wiring and shielding.

An audio plug can carry different wiring arrangements. A TRS connector does not by itself distinguish balanced mono from unbalanced stereo; consult both devices.

Barrel - Audio Cables

Typical Applications

Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.

Headphone amplifier links

Headphone amplifier links

Match the audio plug diameter and stereo contact arrangement to both devices.

Studio patch points

Studio patch points

Check whether the patch panel requires balanced or unbalanced wiring and the specified plug format.

Portable audio connections

Portable audio connections

Confirm the source output and speaker input use compatible analogue audio contacts.

Audio test bench

Audio test bench

Use the specified channel wiring and shielding; connector fit alone does not establish signal compatibility.

Mono audio cables vs. TRS audio cables

Compare the interfaces, construction and selection details of these two product options.

Mono audio cables

Representative listed part: CA-2206.

  • 1st Connector Phone Plug, 3.5mm (1/8"), Right Angle
  • 2nd Connector Cable (Round)
  • Channels Mono
  • Shielding Shielded
  • Length 6.0' (1.83m)
  • Usage Headphones

TRS audio cables

Representative listed part: 770-10040-00100.

  • 1st Connector Phone Plug, 3.5mm (1/8")
  • 2nd Connector Phone Plug, 3.5mm (1/8")
  • Channels Stereo (3 Conductor, TRS)
  • Shielding Shielded
  • Length 3.3' (1.00m)
  • Usage Headphones, Patch Cable

The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.

Frequently Asked Questions

Practical answers to help you prepare your drawing and specifications.

Should I choose mono, TRS or TRRS audio cable?

Compare the Channels attribute with the wiring required by both devices. This family contains different conductor arrangements; a matching plug diameter alone does not establish the required audio or microphone connection.

Check the 1st Connector and 2nd Connector entries independently, including plug or jack, diameter and angle. Choose the arrangement that matches the two equipment ports rather than selecting from the cable name alone.

Review length, shielding, connector angle and intended usage for the exact part. Provide the available clearance around the equipment ports if a straight plug may obstruct installation.

An audio plug can carry different wiring arrangements. A TRS connector does not by itself distinguish balanced mono from unbalanced stereo; consult both devices.

CA-2206 is shown as mono audio cables, with Channels listed as Mono. 770-10040-00100 is shown as trs audio cables, with Channels listed as Stereo (3 Conductor, TRS). These are two examples, not a statement that every part has either specification.

Provide the original manufacturer and complete part number, or a drawing. For this range, compare connector diameter, plug or jack arrangement, contact wiring and shielding. Identify any requirement not covered by the listing rather than selecting only by length or appearance.

Supply a mating-interface drawing and the required connector diameter, plug or jack arrangement, contact wiring and shielding. Add quantity, destination and any inspection requirements. Changes must be reviewed for the selected construction before compatibility, pricing or delivery can be confirmed.

Tell us what you need to build

Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.

  • Engineering review within 24 hours
  • NDA available before drawings are shared
  • Free samples in 5-7 days after drawing approval
Inquiry Drawer

Review & Submit Request

This site uses cookies

We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details