Drawing / 3D file
A 2D drawing, a 3D STEP model or a dimensioned sketch. Tolerances and datums help, but a hand sketch is enough to start.
You do not need a finished drawing package. Any one of these four is enough for an engineer to begin.
A 2D drawing, a 3D STEP model or a dimensioned sketch. Tolerances and datums help, but a hand sketch is enough to start.
A bill of materials, an existing housing MPN or a connector reference. We source and cross-check the mating interfaces.
A sample from a previous supplier works too. We measure it, document it and rebuild it to a controllable specification.
No drawing at all? Describe the environment, the routing space and the signal — our engineers will propose a construction.
See how we move from an initial requirement to design review, sampling and production release. Timing is confirmed for each project.
1
2
3
4
A custom assembly is more than a length and two connectors. These are the six dimensions our engineers work through with you, from the conductor up to the final test record.
28–48AWG stranded or solid conductors, shielded twisted pairs, tinned or bare copper, to match signal, current and flex needs.
Molex, JST, Hirose, JAE, TE/AMP, KEL and equivalent connectors, including micro coaxial and IDC terminations.
Any length, branched harnesses, breakouts, labels and custom pin-outs built exactly to your drawing.
Foil, braided or combination shielding to control EMI/EMC on high-speed display, camera and medical signal lines.
IP67 / IP68 overmolding, strain relief, custom housing and waterproof seals for demanding field environments.
Continuity testing against the approved drawing, plus Hi-pot, pull-force and micro-sections where the agreed inspection plan requires them.
The documents for your project depend on the agreed scope and stage. We can discuss feasibility notes, specifications, inspection plans and production records as needed.
A written yes / no / conditional answer on whether the construction can be built and tested as drawn.
Specific notes on crimp access, strain relief, bend radius and anything that will raise cost or risk.
The wire, terminal, connector and protection combination we would build, with the trade-offs explained.
Unit price at your stated quantities, tooling and sample charges where they apply, and the assumptions behind them.
The drawing revision and build notes the sample was made to, so your validation is against a fixed reference.
Which characteristics are checked, at which stage, with what method and what record is kept.
Agreed packing, labelling and batch record requirements, confirmed before the first release.
Our team coordinates cutting, stripping, crimping, overmolding, micro-coaxial assembly and electrical testing. Changes identified during sampling can be reviewed with the production team before release.
We plan sampling and production together, then confirm the process, capacity and schedule for your specific assembly.
Capacity is an aggregate figure across all product lines. What a single part number can support depends on its construction, tooling and process requirements — we confirm that in the quotation.
Still unsure what to send, or how far we can take your design? The enquiry form below reaches our engineering team directly.
A 2D drawing, 3D STEP model, BOM or connector part number is ideal, but a physical sample or a written description also works as a starting point. Our engineers confirm within 24 business hours and will tell you exactly what is still missing.
Yes. We can sign a mutual NDA before receiving your drawings or BOM. Files are handled only by the engineering team assigned to your project.
After the drawing is approved and materials are confirmed, samples are typically completed in 5–7 business days. Sample charges, if any, are stated in the quotation so there is no surprise later.
Yes. The line that builds your sample runs the production order, so process and records stay consistent. Volume and schedule are confirmed per part number, depending on construction and process requirements. Aggregate factory capacity is up to 10 million pieces per month across all product lines.
You get that answer before tooling, not after. The DFM review lists what has to change, what it costs and what it saves — you decide whether to proceed.
Send a drawing, BOM, connector part number or a brief description of your application. We will review what you have and let you know what else is needed to assess the project.
Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.
We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details