icon ISO 9001 · ISO 13485 · IATF 16949 · ISO 14001 certified manufacturer

Products

Explore products in this family. Open a product for details, or send us your drawing for a custom build.

Part number Description
900002650

0985 706G 103/9M

900004503

0985 YM57530-U 104/3M

900002069

CBL M12-RJ45 05.0M

900004436

0985 YM57530 103/4M

900001995

CBL M12-RJ45 05.0M

900004651

0985 806-U 103/10M

1201088150

M12-4P(D)-MM ST/RJ45 3M

900004206

0985 806 126/10M

1407508

NETWORK CABLE

1407532

NETWORK CABLE

900001992

CBL M12-RJ45 02.0M

900002057

CBL RJ45-PM M12 00.5M Q

900002010

CBL RJ45-PM M12 03.0M Q

900016024

0985 YM57530 104/6M

1407352

NETWORK CABLE

900005105

0985 810 103/3M

900004519

0985 706 104/4M

900004647

0985 806-U 103/6M

E11898

CONNECTION CABLE; ETHERNET CABLE

900004795

0985 808 103/4M

900004736

0985 808-N 103/4M

2096

0985 S4742 104/1,5 M

1300480206

M12 TO RJ45 ENET 3M CORDSET

900000848

0985 S3667 104/0.2M

About Between Series Adapter Cables

Between-Series Adapter Cables includes cable assemblies with different connector series at their two ends.

When selecting an assembly, check both interface standards, pin mapping, shielding and any required conversion.

A change of connector format does not prove protocol, signal-level or power conversion. Confirm whether the selected assembly is passive or contains conversion electronics.

Between Series Adapter Cables

Typical Applications

Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.

Peripheral interface adaptation

Peripheral interface adaptation

Check both interface standards and the full pin mapping; a passive adapter does not convert protocols.

Instrument breakout links

Instrument breakout links

Confirm each breakout connection against the instrument pin assignment and shielding requirements.

Legacy equipment integration

Legacy equipment integration

Verify electrical levels and connector functions before integrating the equipment.

Prototype interface evaluation

Prototype interface evaluation

Compare the source and destination signals before deciding whether conversion electronics are required.

Shielded adapter cables vs. Unshielded adapter cables

Compare the interfaces, construction and selection details of these two product options.

Shielded adapter cables

Representative listed part: 1300480291.

  • Connector Type Circular 04 pos Male to RJ45, 8p4c
  • Cable Type Round
  • Shielding Shielded
  • Length 49.21' (15.00m)
  • Usage Not specified for this example

Unshielded adapter cables

Representative listed part: 1300480369.

  • Connector Type Circular 04 pos Male to RJ45, 8p4c
  • Cable Type Round
  • Shielding Unshielded
  • Length 150.92' (46.00m)
  • Usage Not specified for this example

The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.

Frequently Asked Questions

Practical answers to help you prepare your drawing and specifications.

Does a between-series cable guarantee that two devices can communicate?

Confirm the source and destination interfaces, signal assignment and equipment requirements. A cable listing that connects two connector series is not, by itself, evidence of electronic conversion or protocol compatibility.

Read the complete Connector Type entry, including position and contact counts. Obtain or compare the wiring diagram so each required signal reaches the intended contact at the other end.

Review the listed Shielding and Cable Type together with both connector terminations. If grounding continuity or shield termination is important, include that requirement in the enquiry and request confirmation for the exact part.

A change of connector format does not prove protocol, signal-level or power conversion. Confirm whether the selected assembly is passive or contains conversion electronics.

1300480291 is shown as shielded adapter cables, with Shielding listed as Shielded. 1300480369 is shown as unshielded adapter cables, with Shielding listed as Unshielded. These are two examples, not a statement that every part has either specification.

Provide the original manufacturer and complete part number, or a drawing. For this range, compare both interface standards, pin mapping, shielding and any required conversion. Identify any requirement not covered by the listing rather than selecting only by length or appearance.

Supply a mating-interface drawing and the required both interface standards, pin mapping, shielding and any required conversion. Add quantity, destination and any inspection requirements. Changes must be reviewed for the selected construction before compatibility, pricing or delivery can be confirmed.

Tell us what you need to build

Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.

  • Engineering review within 24 hours
  • NDA available before drawings are shared
  • Free samples in 5-7 days after drawing approval
Inquiry Drawer

Review & Submit Request

This site uses cookies

We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details