icon ISO 9001 · ISO 13485 · IATF 16949 · ISO 14001 certified manufacturer

Products

Explore products in this family. Open a product for details, or send us your drawing for a custom build.

Part number Description
USBA11850M52XLCP(R

CBL ASSY PLUG TO USB A PLG 1.64'

743-60012-00200

MINI DP/M TO VGA/M CONN

2821722-1

IFP/LEC CBL ASSY 1 PORT TYPE B S

1321001-03

CBL DVI(12+5) CON 3' 28 AWG

USBA11850M52XCCP(R)

CBL ASSY PLUG TO USB A PLG 1.64'

0985 806 103/2M

CABLE ETHERNET M12-RJ45 2M

CMB11850M5MICB2(R)

CBL ASSY JACK - MCR B PLG 1.64'

142M4D25020

M12 ETHERNET CABLE, IP67, D-CODE

0985 YM57530 103/10M

CABLE ETHERNET M12-RJ45 10M

U209-006-RJ45-X

USB TO RJ45 CISCO SERIAL ROLLOVE

4182

3.5MM MONO AUDIO JACK TO ALLIGAT

UB-20PMFP-LC7003

USB WITH HARNESS

UA-20PMFP-SC8003

USB WITH HARNESS

628-000-906-2

CABLE ASSEMBLY

U444-003-HWE

USB-C TO HDMI ADAPTER CABLE (M/M

10-02462

CBL 2.1X5.5MM JACK-GATOR CLIPS

10-02402

CBL ASSY SAE TO 2.1X5.5 JACK 3'

1300480308

MIC 4P M/MP ST/RJ45 D-CODED 20M

10-02403

CBL ASSY SAE TO 2.5X5.5 JACK 3'

USBA7001M0T00(R)

CBL ASSY CIRC 2P F-M USB-A 3.28'

MP-5FRJ45SLPS-001

FLAT 8X8 RJ45 W/ SPADE LUGS, 1'

1300580303

ULTRA-LOCK D-CODE M12 TO RJ45 4M

1300480349

MIC 4P M/MP ST/RJ45 D-CODED 3M

900016073

0985 856 103/40M

About Between Series Adapter Cables

Between-Series Adapter Cables includes cable assemblies with different connector series at their two ends.

When selecting an assembly, check both interface standards, pin mapping, shielding and any required conversion.

A change of connector format does not prove protocol, signal-level or power conversion. Confirm whether the selected assembly is passive or contains conversion electronics.

Between Series Adapter Cables

Typical Applications

Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.

Peripheral interface adaptation

Peripheral interface adaptation

Check both interface standards and the full pin mapping; a passive adapter does not convert protocols.

Instrument breakout links

Instrument breakout links

Confirm each breakout connection against the instrument pin assignment and shielding requirements.

Legacy equipment integration

Legacy equipment integration

Verify electrical levels and connector functions before integrating the equipment.

Prototype interface evaluation

Prototype interface evaluation

Compare the source and destination signals before deciding whether conversion electronics are required.

Shielded adapter cables vs. Unshielded adapter cables

Compare the interfaces, construction and selection details of these two product options.

Shielded adapter cables

Representative listed part: 1300480291.

  • Connector Type Circular 04 pos Male to RJ45, 8p4c
  • Cable Type Round
  • Shielding Shielded
  • Length 49.21' (15.00m)
  • Usage Not specified for this example

Unshielded adapter cables

Representative listed part: 1300480369.

  • Connector Type Circular 04 pos Male to RJ45, 8p4c
  • Cable Type Round
  • Shielding Unshielded
  • Length 150.92' (46.00m)
  • Usage Not specified for this example

The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.

Frequently Asked Questions

Practical answers to help you prepare your drawing and specifications.

Does a between-series cable guarantee that two devices can communicate?

Confirm the source and destination interfaces, signal assignment and equipment requirements. A cable listing that connects two connector series is not, by itself, evidence of electronic conversion or protocol compatibility.

Read the complete Connector Type entry, including position and contact counts. Obtain or compare the wiring diagram so each required signal reaches the intended contact at the other end.

Review the listed Shielding and Cable Type together with both connector terminations. If grounding continuity or shield termination is important, include that requirement in the enquiry and request confirmation for the exact part.

A change of connector format does not prove protocol, signal-level or power conversion. Confirm whether the selected assembly is passive or contains conversion electronics.

1300480291 is shown as shielded adapter cables, with Shielding listed as Shielded. 1300480369 is shown as unshielded adapter cables, with Shielding listed as Unshielded. These are two examples, not a statement that every part has either specification.

Provide the original manufacturer and complete part number, or a drawing. For this range, compare both interface standards, pin mapping, shielding and any required conversion. Identify any requirement not covered by the listing rather than selecting only by length or appearance.

Supply a mating-interface drawing and the required both interface standards, pin mapping, shielding and any required conversion. Add quantity, destination and any inspection requirements. Changes must be reviewed for the selected construction before compatibility, pricing or delivery can be confirmed.

Tell us what you need to build

Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.

  • Engineering review within 24 hours
  • NDA available before drawings are shared
  • Free samples in 5-7 days after drawing approval
Inquiry Drawer

Review & Submit Request

This site uses cookies

We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details