Connector assembly
Contacts - Leadframe can be evaluated for connector assembly. Match contact geometry, termination, plating and mating system to the equipment interface.
Explore products in this family. Open a product for details, or send us your drawing for a custom build.
| Part number | Description |
|---|---|
| 1544425-1 | SIL CONTACT Y1 THROUGH HOLE |
| 1544162-2 | SIL CONTACT Y1 THROUGH HOLE |
| 1544172-2 | DIL CONTACT Y1 THROUGH HOLE |
| 1544146-4 | LEADFRAME 2.54MM CLIP |
| 1544210-2 | SIL CONTACT Y1 THROUGH HOLE |
| 1544169-1 | DIL CONTACT F1 THROUGH HOLE |
| 1544146-2 | DIL CONTACT F1 THROUGH HOLE |
| 1544174-1 | DIL CONTACT F1 THROUGH HOLE |
| 1544146-1 | DIL CONTACT F1 THROUGH HOLE |
| 1544400-1 | SIL CONTACT Y1 THROUGH HOLE |
| 1544290-1 | SIL CONTACT Y1 THROUGH HOLE |
| 1544281-1 | SIL CONTACT Y1 THROUGH HOLE |
| 1544426-2 | SIL CONTACT Y1 THROUGH HOLE |
| 1544296-1 | SIL CONTACT Y1 THROUGH HOLE |
| 1544426-1 | SIL CONTACT Y1 THROUGH HOLE |
The Contacts - Leadframe range covers separate conductive contact elements for compatible interconnection systems.
Compare contact geometry, termination, plating and mating system for the required installation. These are separate conductive contacts. Match the contact to its housing, wire range and specified termination tooling.
Review Clip Style, Clip Type, Clip Length, Pin Length and Termination on the individual product page before choosing a part.
Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.
Contacts - Leadframe can be evaluated for connector assembly. Match contact geometry, termination, plating and mating system to the equipment interface.
For circuit interfaces, verify Clip Style, Clip Type, Clip Length, Pin Length and Termination on the selected Contacts - Leadframe. These are separate conductive contacts. Match the contact to its housing, wire range and specified termination tooling.
In contact verification, allow for the required mounting, routing or termination space. Check contact geometry, termination, plating and mating system before assembly.
For contacts - leadframe inspection, identify the original Contacts - Leadframe part number and mating arrangement. Compare Clip Style, Clip Type, Clip Length, Pin Length and Termination before substitution.
Compare the interfaces, construction and selection details of these two product options.
Example: 1544426-1
Example: 1544296-1
The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.
Practical answers to help you prepare your drawing and specifications.
This category covers separate conductive contact elements for compatible interconnection systems. These are separate conductive contacts. Match the contact to its housing, wire range and specified termination tooling.
Examples in this category include 0.050" (1.27mm) and 0.100" (2.54mm). Match the selected Contacts - Leadframe to the required contact geometry, termination, plating and mating system.
For Contacts - Leadframe, check Clip Style, Clip Type, Clip Length, Pin Length and Termination against the equipment or mating-part drawing. Confirm the installed clearance and termination access as well as the nominal interface size.
Check contact geometry, termination, plating and mating system for the selected part. Use its stated operating conditions and complete assembly requirements; appearance alone does not establish the electrical or environmental rating.
These are separate conductive contacts. Match the contact to its housing, wire range and specified termination tooling. For Contacts - Leadframe, identify the matching system and required assembly parts before ordering.
1544426-1 specifies Clip Style: SIL and Clip Type: Y1. 1544296-1 specifies Clip Style: SIL and Clip Type: Y1. Check the full mating and installation requirements before treating different Contacts - Leadframe as replacements.
Send the manufacturer and full part number, quantity and required delivery destination. For this category, include contact geometry, termination, plating and mating system and a mating or installation drawing when a replacement is needed.
Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.
We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details