Serial controller links
Confirm the serial standard and pinout; a D-sub shell does not identify the electrical interface.
Explore products in this family. Open a product for details, or send us your drawing for a custom build.
| Part number | Description |
|---|---|
| DCDM-25S6E5-18.0B | CABLE ASY D TO MIC D 25P 457.2MM |
| DCDM-25S6E5-18.0K | CABLE ASY D TO MIC D 25P 457.2MM |
| DCDM-15P6E5-18.0B | CABLE ASY D TO MIC D 15P 457.2MM |
| MDM-51PH048F-A174 | MICRO 51C P 48" RBW FLOAT NI |
| MDM-15PH002F-F222 | MICRO 15C P 12" RBW FLOAT HT |
| P502-040 | CABLE ASSY HD15 SHLD BLK 12.19M |
| RMDM-51PH003K | MICRO 51C PIN 18" RBW JACKS NI |
| RMTB1-15PHY0102 | CABLE ASSY MICRO 15C PIN 18/11 |
| MDM-51PH048K-A174 | MICRO 51C P 48" RBW JACKS NI |
| DCDM-15S6E5-36.0B | CABLE ASY D TO MIC D 15P 914.4MM |
| MDM-51PH041F-A174 | MICRO 51C P 120" RBW FLOAT NI |
| MDM-51PH034F-A174 | CABLE ASY D TO WIRE 51P 203.2MM |
| MDM-51PH034L-A174 | CABLE ASY D TO WIRE 51P 203.2MM |
| MDM-51PH006K-A174 | CABLE ASY D TO WIRE 51P 914.4MM |
| A7MFB-3706M | CABLE D-SUB-AMP37B/AE37M/AFP37B |
| MDM-15PH002L-F222 | MICRO 15C P 12" RBW JACKSLP HT |
| MDM-100PH003M12-A174 | MICRO 100 M 18" RBW A174 |
| MDM-51PH041K-A174 | MICRO 51C P 120" RBW JACKS NI |
| RMDM-9SH003F | MICRO 9C S 18" RBW FLOAT NI |
| MDM-51PH034K-A174 | CABLE ASY D TO WIRE 51P 203.2MM |
| MDM-51PH025L-A174 | CABLE ASSY D TO WIRE 51P 254MM |
| MDM-51PH025K-A174 | CABLE ASSY D TO WIRE 51P 254MM |
| MDM-51PH005L-A174 | CABLE ASSY D TO WIRE 51P 762MM |
| MDM-51PH016L-A174 | MICRO 51C P 6" RBW JACKS NI |
D-Sub Cable Assemblies includes D-sub interconnects with different contact counts and end configurations.
When selecting an assembly, check contact count, gender, pinout, mounting hardware and cable shielding.
Straight-through, crossover and equipment-specific D-sub cables may use similar shells. Confirm the pin-to-pin map instead of inferring it from the connector size.
Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.
Confirm the serial standard and pinout; a D-sub shell does not identify the electrical interface.
Check contact count, gender and screw-lock hardware against the instrument drawing.
Distinguish straight-through, crossover and equipment-specific wiring before replacement.
Match both ends and allow clearance for the backshell, mounting screws and cable bend.
Compare the interfaces, construction and selection details of these two product options.
Representative listed part: 1200980207.
Representative listed part: M7OOK-0906J.
The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.
Practical answers to help you prepare your drawing and specifications.
Check both mating ends and obtain the pin-to-pin wiring required by the equipment. Position count identifies only part of the connection; it does not document straight-through wiring, crossovers or unused contacts.
Read the contact description at both ends and compare it with the equipment connector. Specify the shell size, position count and retention arrangement as well as male pins or female sockets.
Confirm the lead identification, length and termination requirements for the installation. A connector-to-leads assembly requires a defined wiring plan rather than the same mating arrangement as a fully terminated cable.
Straight-through, crossover and equipment-specific D-sub cables may use similar shells. Confirm the pin-to-pin map instead of inferring it from the connector size.
1200980207 is shown as male d-sub termination, with 1st Connector listed as Plug, Male Pins. M7OOK-0906J is shown as female d-sub termination, with 1st Connector listed as Receptacle, Female Sockets. These are two examples, not a statement that every part has either specification.
Provide the original manufacturer and complete part number, or a drawing. For this range, compare contact count, gender, pinout, mounting hardware and cable shielding. Identify any requirement not covered by the listing rather than selecting only by length or appearance.
Supply a mating-interface drawing and the required contact count, gender, pinout, mounting hardware and cable shielding. Add quantity, destination and any inspection requirements. Changes must be reviewed for the selected construction before compatibility, pricing or delivery can be confirmed.
Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.
We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details