Serial controller links
Confirm the serial standard and pinout; a D-sub shell does not identify the electrical interface.
Explore products in this family. Open a product for details, or send us your drawing for a custom build.
| Part number | Description |
|---|---|
| MDM-9PH059K-A174 | MICRO 9C P 72" WHT JACKS NI |
| MDM-31PH008B | MICRO 31C P 12" WHT |
| MDM-25SH023P | CABLE ASSY D TO WIRE 25P 508MM |
| MDM-15PH004F | CABLE ASY D TO WIRE 15P 609.6MM |
| MDM-9PH041L-A174 | MICRO 9C P 120" RBW JACKS NI |
| MDM-51SH008B-A174 | MICRO 51C S 12" WHT NI |
| 2926548 | CABLE ASSY DB25 SHIELDED GRAY 3M |
| DCDM-21S6E5-18.0F | CABLE ASY D TO MIC D 21P 457.2MM |
| MDM-25SH046M7-A174 | MICRO 25 SKT 72" RBW JACKP |
| MDM-25SH046P-A174 | MICRO 25C S 72" RBW JACKP NI |
| MDM-25SH001B | CABLE ASY D TO WIRE 25P 457.2MM |
| MDM-31PH017L-A174 | MICRO 31C P 72" YEL JACKS NI |
| MDM-25PH003A | MICRO 25 M 18' RBW |
| MDM-21PHC26L-A174 | MICRO 21C P 8" WHT JACKS NI |
| MDM03-C21-12 | CABLE ASY D TO WIRE 21P 914.4MM |
| MDM-31SHC10B | MICRO 31C S 30" WHT |
| MDM-9PH042L | MICRO 9C P 120" YEL JACKS |
| MDM-37PH008B-A174 | MICRO 37C P 12" WHT NI |
| MDM-21SHC10F-A174 | MICRO 21C S 30" WHT FLOAT NI |
| MDB1-7C2SH009K | MICRO |
| MDM-31SHC38P | MICRO 31C S 20" WHT JACKP |
| MDM-21PH047F-A174 | CABLE ASY D TO WIRE 21P 152.4MM |
| MDM-37PH028B-A174 | CABLE ASY D TO WIRE 37P 304.8MM |
| MDM-37PHC26P-A174 | MICRO 37C P 8" WHT JACKP NI |
D-Sub Cable Assemblies includes D-sub interconnects with different contact counts and end configurations.
When selecting an assembly, check contact count, gender, pinout, mounting hardware and cable shielding.
Straight-through, crossover and equipment-specific D-sub cables may use similar shells. Confirm the pin-to-pin map instead of inferring it from the connector size.
Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.
Confirm the serial standard and pinout; a D-sub shell does not identify the electrical interface.
Check contact count, gender and screw-lock hardware against the instrument drawing.
Distinguish straight-through, crossover and equipment-specific wiring before replacement.
Match both ends and allow clearance for the backshell, mounting screws and cable bend.
Compare the interfaces, construction and selection details of these two product options.
Representative listed part: 1200980207.
Representative listed part: M7OOK-0906J.
The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.
Practical answers to help you prepare your drawing and specifications.
Check both mating ends and obtain the pin-to-pin wiring required by the equipment. Position count identifies only part of the connection; it does not document straight-through wiring, crossovers or unused contacts.
Read the contact description at both ends and compare it with the equipment connector. Specify the shell size, position count and retention arrangement as well as male pins or female sockets.
Confirm the lead identification, length and termination requirements for the installation. A connector-to-leads assembly requires a defined wiring plan rather than the same mating arrangement as a fully terminated cable.
Straight-through, crossover and equipment-specific D-sub cables may use similar shells. Confirm the pin-to-pin map instead of inferring it from the connector size.
1200980207 is shown as male d-sub termination, with 1st Connector listed as Plug, Male Pins. M7OOK-0906J is shown as female d-sub termination, with 1st Connector listed as Receptacle, Female Sockets. These are two examples, not a statement that every part has either specification.
Provide the original manufacturer and complete part number, or a drawing. For this range, compare contact count, gender, pinout, mounting hardware and cable shielding. Identify any requirement not covered by the listing rather than selecting only by length or appearance.
Supply a mating-interface drawing and the required contact count, gender, pinout, mounting hardware and cable shielding. Add quantity, destination and any inspection requirements. Changes must be reviewed for the selected construction before compatibility, pricing or delivery can be confirmed.
Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.
We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details