icon ISO 9001 · ISO 13485 · IATF 16949 · ISO 14001 certified manufacturer

Products

Explore products in this family. Open a product for details, or send us your drawing for a custom build.

Part number Description
MDM-21PHW11B

MICRO

MDM-37SH013F-A174

CABLE ASSY D TO WIRE 37P 1.22M

MDM-51SH010K-A174

MICRO 51C S 30" YEL JACKS NI

MDM04-D25-13A174

CABLE ASSY D TO WIRE 25P 1.83M

MDM-25PH006K

CABLE ASY D TO WIRE 25P 914.4MM

MDM-51PH010P

MICRO 51C P 30" YEL JACKP

MDM-25PH059K-A174

MICRO 25C P 72" WHT JACKS NI

DCDM-15P6E5-18.0L

CABLE ASY D TO MIC D 15P 457.2MM

969M101-24-1TPS-CA012

CABLE ASSY DB25 SHLD CLR 3.66M

1532269-4

M83513/22-D01NP = MCKS-N1-P-25PS

MDM-25PH048K-A174

CABLE ASSY D TO WIRE 25P 1.22M

MDB1-31PH003K

MICRO

MDB1-25SH003P

MICRO

MDM-31SH006K-A174

CABLE ASY D TO WIRE 31P 914.4MM

MDM-31SHC42K-A174

MICRO 31C S 120" WHT JACKS NI

MDM-31PH88

MICRO 31 PIN 88" COLOR CODED

MDM-21PH034P-A174

CABLE ASY D TO WIRE 21P 203.2MM

MDM-21PH167M5

MICRO

MDM-51SH013K-A174

MICRO 51C S 48" YEL JACKS NI

MDM-9PH067B-A172

MICRO 9 M 5" WHT A174

MDM-9PH003A-A172

MICRO

MDB1-25SH001P

MICRO

MDM-9PH003B-A172

MICRO

MDM-31PH048M5

MDM-31PH048M5

About D-Sub Cables

D-Sub Cable Assemblies includes D-sub interconnects with different contact counts and end configurations.

When selecting an assembly, check contact count, gender, pinout, mounting hardware and cable shielding.

Straight-through, crossover and equipment-specific D-sub cables may use similar shells. Confirm the pin-to-pin map instead of inferring it from the connector size.

D-Sub Cables

Typical Applications

Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.

Serial controller links

Serial controller links

Confirm the serial standard and pinout; a D-sub shell does not identify the electrical interface.

Instrument rear-panel wiring

Instrument rear-panel wiring

Check contact count, gender and screw-lock hardware against the instrument drawing.

Legacy workstation servicing

Legacy workstation servicing

Distinguish straight-through, crossover and equipment-specific wiring before replacement.

Panel extension routing

Panel extension routing

Match both ends and allow clearance for the backshell, mounting screws and cable bend.

Male D-sub termination vs. Female D-sub termination

Compare the interfaces, construction and selection details of these two product options.

Male D-sub termination

Representative listed part: 1200980207.

  • 1st Connector Plug, Male Pins
  • 2nd Connector Plug, Male Pins (2), Right Angle
  • Type DB9
  • Number of Positions 9
  • Shielding Shielded
  • Length 3.28' (1.00m)

Female D-sub termination

Representative listed part: M7OOK-0906J.

  • 1st Connector Receptacle, Female Sockets
  • 2nd Connector Receptacle, Female Sockets
  • Type DB9
  • Number of Positions 9
  • Shielding Unshielded
  • Length 6.00' (1.83m)

The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.

Frequently Asked Questions

Practical answers to help you prepare your drawing and specifications.

Are D-sub cables with the same pin count wired identically?

Check both mating ends and obtain the pin-to-pin wiring required by the equipment. Position count identifies only part of the connection; it does not document straight-through wiring, crossovers or unused contacts.

Read the contact description at both ends and compare it with the equipment connector. Specify the shell size, position count and retention arrangement as well as male pins or female sockets.

Confirm the lead identification, length and termination requirements for the installation. A connector-to-leads assembly requires a defined wiring plan rather than the same mating arrangement as a fully terminated cable.

Straight-through, crossover and equipment-specific D-sub cables may use similar shells. Confirm the pin-to-pin map instead of inferring it from the connector size.

1200980207 is shown as male d-sub termination, with 1st Connector listed as Plug, Male Pins. M7OOK-0906J is shown as female d-sub termination, with 1st Connector listed as Receptacle, Female Sockets. These are two examples, not a statement that every part has either specification.

Provide the original manufacturer and complete part number, or a drawing. For this range, compare contact count, gender, pinout, mounting hardware and cable shielding. Identify any requirement not covered by the listing rather than selecting only by length or appearance.

Supply a mating-interface drawing and the required contact count, gender, pinout, mounting hardware and cable shielding. Add quantity, destination and any inspection requirements. Changes must be reviewed for the selected construction before compatibility, pricing or delivery can be confirmed.

Tell us what you need to build

Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.

  • Engineering review within 24 hours
  • NDA available before drawings are shared
  • Free samples in 5-7 days after drawing approval
Inquiry Drawer

Review & Submit Request

This site uses cookies

We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details