icon ISO 9001 · ISO 13485 · IATF 16949 · ISO 14001 certified manufacturer

Products

Explore products in this family. Open a product for details, or send us your drawing for a custom build.

Part number Description
CS-DSSMDB9MF0-025

CABLE ASSY DB09 SHLD GRY 7.62M

834219043

CABLE ASY D TO MICR D 9P 914.4MM

A7FFB-0906G

CABLE D-SUB-AFP09B/AE09G/AFP09B

CS-DSDMDB15MF-015

CABLE ASSY DB15 SHLD GRAY 4.57M

CS-DSDHD15MF0-015

CABLE ASSY HD15 SHLD GRAY 4.57M

1656301

CABLE ASSY DB25 SHIELDED GRAY 2M

1656291

CABLE ASSY DB25 SHIELDED GRAY 1M

1656275

CABLE ASSY DB15 SHIELDED GRAY 2M

CS-DSDMDB15MM-002.5

CABLE ASSY DB15 SHLD GRAY 762MM

CS-DSDHD15MM0-010

CABLE ASSY HD15 SHLD GRAY 3.05M

CS-DSDHD15MF0-010

CABLE ASSY HD15 SHLD GRAY 3.05M

AK162-3

CABLE ASSY DB25 SHLD BEIGE 3M

CS-DSDHD15MF0-007.5

CABLE ASSY HD15 SHLD GRAY 2.29M

A7OXB-2506G

CABLE D-SUB - AFN25B/AE25G/X

CS-DSDMDB09MF-003

CABLE ASSY DB09 SHLD GRY 914.4MM

CS-DSNULW19FF-005

CABLE ASSY DB09 SHLD GRY 1.52M

CS-DSDHD15MF0-005

CABLE ASSY HD15 SHLD GRAY 1.52M

P516-001-HR

CABLE ASSY HD15 SHLD BLK 304.8MM

P516-001

CABLE ASSY HD15 SHLD BLK 304.8MM

P502-003-RA

CABLE ASSY HD15 SHLD BLK 914.4MM

CA-VGA-M-M-6FT

VGA PLUG TO VGA PLUG, 6FT

P502-010

CABLE ASSY HD15 SHLD BLACK 3.05M

P502-006-SM

CABLE ASSY HD15 SHLD BLACK 1.83M

P510-006

CABLE ASSY HD15 SHLD BLACK 1.83M

About D-Sub Cables

D-Sub Cable Assemblies includes D-sub interconnects with different contact counts and end configurations.

When selecting an assembly, check contact count, gender, pinout, mounting hardware and cable shielding.

Straight-through, crossover and equipment-specific D-sub cables may use similar shells. Confirm the pin-to-pin map instead of inferring it from the connector size.

D-Sub Cables

Typical Applications

Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.

Serial controller links

Serial controller links

Confirm the serial standard and pinout; a D-sub shell does not identify the electrical interface.

Instrument rear-panel wiring

Instrument rear-panel wiring

Check contact count, gender and screw-lock hardware against the instrument drawing.

Legacy workstation servicing

Legacy workstation servicing

Distinguish straight-through, crossover and equipment-specific wiring before replacement.

Panel extension routing

Panel extension routing

Match both ends and allow clearance for the backshell, mounting screws and cable bend.

Male D-sub termination vs. Female D-sub termination

Compare the interfaces, construction and selection details of these two product options.

Male D-sub termination

Representative listed part: 1200980207.

  • 1st Connector Plug, Male Pins
  • 2nd Connector Plug, Male Pins (2), Right Angle
  • Type DB9
  • Number of Positions 9
  • Shielding Shielded
  • Length 3.28' (1.00m)

Female D-sub termination

Representative listed part: M7OOK-0906J.

  • 1st Connector Receptacle, Female Sockets
  • 2nd Connector Receptacle, Female Sockets
  • Type DB9
  • Number of Positions 9
  • Shielding Unshielded
  • Length 6.00' (1.83m)

The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.

Frequently Asked Questions

Practical answers to help you prepare your drawing and specifications.

Are D-sub cables with the same pin count wired identically?

Check both mating ends and obtain the pin-to-pin wiring required by the equipment. Position count identifies only part of the connection; it does not document straight-through wiring, crossovers or unused contacts.

Read the contact description at both ends and compare it with the equipment connector. Specify the shell size, position count and retention arrangement as well as male pins or female sockets.

Confirm the lead identification, length and termination requirements for the installation. A connector-to-leads assembly requires a defined wiring plan rather than the same mating arrangement as a fully terminated cable.

Straight-through, crossover and equipment-specific D-sub cables may use similar shells. Confirm the pin-to-pin map instead of inferring it from the connector size.

1200980207 is shown as male d-sub termination, with 1st Connector listed as Plug, Male Pins. M7OOK-0906J is shown as female d-sub termination, with 1st Connector listed as Receptacle, Female Sockets. These are two examples, not a statement that every part has either specification.

Provide the original manufacturer and complete part number, or a drawing. For this range, compare contact count, gender, pinout, mounting hardware and cable shielding. Identify any requirement not covered by the listing rather than selecting only by length or appearance.

Supply a mating-interface drawing and the required contact count, gender, pinout, mounting hardware and cable shielding. Add quantity, destination and any inspection requirements. Changes must be reviewed for the selected construction before compatibility, pricing or delivery can be confirmed.

Tell us what you need to build

Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.

  • Engineering review within 24 hours
  • NDA available before drawings are shared
  • Free samples in 5-7 days after drawing approval
Inquiry Drawer

Review & Submit Request

This site uses cookies

We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details