icon ISO 9001 · ISO 13485 · IATF 16949 · ISO 14001 certified manufacturer

Products

Explore products in this family. Open a product for details, or send us your drawing for a custom build.

Part number Description
MDM-15PHC26L

MICRO 15C P 8" WHT JACKS

MDM-15PHC26F-A174

MICRO 15C P 8" WHT FLOAT NI

MDM-15PHC26B-A174

MICRO 15C P 8" WHT NI

MDM-15PHC13L-A174

MICRO 15C P 48" WHT JACKS NI

MDM-15PHC26F

MICRO 15C P 8" WHT FLOAT

MDM-15PHC20P

MICRO 15C P 3" WHT JACKP

MD1-9SH87

MICRO CLIP MT 9 F PLASTIC

CA111972-52

MDSM CABLE ASSEMBLY

MDM03-G51-03A174

MICRO 51C P /11 18' 10 CR NI

MDM03-A9-05

MICRO 9C P AU 5' GLD

MDM03-D25-07A174

MICRO 25C P SN .5' SLV NI

MDM04-A9-06

MICRO 9C S AU 1' GLD

MDB1-9PL56

MICRO 9 M .150" UNINS

MDM03-D25-09A174

MICRO 25C P /33 18' WHT NI

MDM03-F37-07A174

MICRO 37C P SN .5' SLV NI

MDM03-G51-10

MICRO 51C P /33 36 WHT

MDM025SH028K

MICRO 25 F 12" YEL JACKS

MDM03-D25-05A174

MICRO 25C P AU 5' GLD NI

MDM03-B15-05A174

MICRO 15C P AU 5' GLD NI

MDB1-51SH026

MDB1-51SH026

MDB1-51SH029

MDB1-51SH029

MDM03-C21-05

MICRO 21C P AU 5' GLD

MDEM-9PH003B-A174

MDEM-9PH003B-A174

MDB1-25PL2

095484-0023

About D-Sub Cables

D-Sub Cable Assemblies includes D-sub interconnects with different contact counts and end configurations.

When selecting an assembly, check contact count, gender, pinout, mounting hardware and cable shielding.

Straight-through, crossover and equipment-specific D-sub cables may use similar shells. Confirm the pin-to-pin map instead of inferring it from the connector size.

D-Sub Cables

Typical Applications

Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.

Serial controller links

Serial controller links

Confirm the serial standard and pinout; a D-sub shell does not identify the electrical interface.

Instrument rear-panel wiring

Instrument rear-panel wiring

Check contact count, gender and screw-lock hardware against the instrument drawing.

Legacy workstation servicing

Legacy workstation servicing

Distinguish straight-through, crossover and equipment-specific wiring before replacement.

Panel extension routing

Panel extension routing

Match both ends and allow clearance for the backshell, mounting screws and cable bend.

Male D-sub termination vs. Female D-sub termination

Compare the interfaces, construction and selection details of these two product options.

Male D-sub termination

Representative listed part: 1200980207.

  • 1st Connector Plug, Male Pins
  • 2nd Connector Plug, Male Pins (2), Right Angle
  • Type DB9
  • Number of Positions 9
  • Shielding Shielded
  • Length 3.28' (1.00m)

Female D-sub termination

Representative listed part: M7OOK-0906J.

  • 1st Connector Receptacle, Female Sockets
  • 2nd Connector Receptacle, Female Sockets
  • Type DB9
  • Number of Positions 9
  • Shielding Unshielded
  • Length 6.00' (1.83m)

The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.

Frequently Asked Questions

Practical answers to help you prepare your drawing and specifications.

Are D-sub cables with the same pin count wired identically?

Check both mating ends and obtain the pin-to-pin wiring required by the equipment. Position count identifies only part of the connection; it does not document straight-through wiring, crossovers or unused contacts.

Read the contact description at both ends and compare it with the equipment connector. Specify the shell size, position count and retention arrangement as well as male pins or female sockets.

Confirm the lead identification, length and termination requirements for the installation. A connector-to-leads assembly requires a defined wiring plan rather than the same mating arrangement as a fully terminated cable.

Straight-through, crossover and equipment-specific D-sub cables may use similar shells. Confirm the pin-to-pin map instead of inferring it from the connector size.

1200980207 is shown as male d-sub termination, with 1st Connector listed as Plug, Male Pins. M7OOK-0906J is shown as female d-sub termination, with 1st Connector listed as Receptacle, Female Sockets. These are two examples, not a statement that every part has either specification.

Provide the original manufacturer and complete part number, or a drawing. For this range, compare contact count, gender, pinout, mounting hardware and cable shielding. Identify any requirement not covered by the listing rather than selecting only by length or appearance.

Supply a mating-interface drawing and the required contact count, gender, pinout, mounting hardware and cable shielding. Add quantity, destination and any inspection requirements. Changes must be reviewed for the selected construction before compatibility, pricing or delivery can be confirmed.

Tell us what you need to build

Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.

  • Engineering review within 24 hours
  • NDA available before drawings are shared
  • Free samples in 5-7 days after drawing approval
Inquiry Drawer

Review & Submit Request

This site uses cookies

We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details