High-speed equipment links
Match the connector family, protocol and supported equipment port.
Explore products in this family. Open a product for details, or send us your drawing for a custom build.
| Part number | Description |
|---|---|
| 1001890463 | 4X HD SHORT BODY 250MM 00KF830 |
| FCBR410QB1C50 | CABLE OPT 4X10 GBPS FULL-DUPLEX, |
| 1001890213 | 2* (4X HD TO 2*4X HD) SHORT 280M |
| 745464182 | 16X TO (2) 8X PCIE, STANDARD PIN |
| FCBR410QB1CX0 | CABLE OPT 4X10 GBPS FULL-DUPLEX, |
| 2150711005 | 2XMCIO 8X STR TO SLIMSAS 8X STR |
| 745464180 | 16X TO (2) 8X PCIE, STANDARD PIN |
| 1110752002 | IPASS X4 HD TO HD 3.0, 2M, 69197 |
| 1110751211 | 4X MINISAS HD TO SFP+ 2.0M 28AWG |
| 747577601 | QSFPQSFP CU PATCH CBL 1M 26AWG |
| 1003461101 | ZQSFP+ TO 2ZQSFP+ 50G CBL ASSY 1 |
| 2050583020 | NPIO 8X STR TO 2* 4X RA, 750MM |
| 747529720 | SFP+ CU CBL ASSLY 10G 3M 30AWG N |
| 2060611153 | NPIO 4X STR-NPIO 4XSTR W/SIDEBND |
| 1001890417 | 4X INTERNAL HD SHORT BODY, 950MM |
| 2002280103 | 4X ZHD STR TO STR, 600MM, CTRL T |
| 2073722179 | SLIMSAS 4X STR + POWER TO M.2 + |
| 1110753005 | CABLE , 1.5M HD-MISAS |
| 745095011 | 12X ASSY, 30 AWG, 16 PR BNDLD-1. |
| 1001890211 | 2*4X HD STR SHORT 340MM |
| 1003463272 | ZQSFP+ TO 2ZQSFP+ 26AWG 2.75M CB |
| 2015912004 | DDQ TO DDQ 25G 2M 32AWG CBL ASSY |
| 2002260212 | RVB NPIO8X 85OM LAB PCBA FINAL |
| 1004364019 | 4X NPIO TO HD, .370M FLAT CABLE, |
Pluggable Cable Assemblies includes pluggable equipment interconnects with interface and retention options.
When selecting an assembly, check connector family, protocol support, active or passive design and retention.
Confirm the exact port and equipment compatibility. Similar connector envelopes do not establish supported data rate or active-cable operation.
Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.
Match the connector family, protocol and supported equipment port.
Check cable length, retention and active or passive design against the port requirements.
Confirm the exact interface and equipment compatibility before replacement.
Check latch access and connector orientation as well as electrical compatibility.
Compare the interfaces, construction and selection details of these two product options.
Representative listed part: 1110251208.
Representative listed part: 2015911010.
The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.
Practical answers to help you prepare your drawing and specifications.
Check Cable Connectors, Connector Type and Gender at both ends, together with the equipment-supported interface. Similar module housings do not establish compatible electrical or signalling requirements.
Use the Features attribute and the equipment compatibility information for the exact part. Confirm the supported link and length; do not assume an active and passive assembly are direct substitutes.
Review Fastening Type, pull-tab clearance and Cable Type before specifying the installation. Provide the port spacing and routing constraints if the connector body or release mechanism has limited access.
Confirm the exact port and equipment compatibility. Similar connector envelopes do not establish supported data rate or active-cable operation.
1110251208 is shown as shielded pluggable cables, with Shielding listed as Shielded. 2015911010 is shown as unshielded pluggable cables, with Shielding listed as Unshielded. These are two examples, not a statement that every part has either specification.
Provide the original manufacturer and complete part number, or a drawing. For this range, compare connector family, protocol support, active or passive design and retention. Identify any requirement not covered by the listing rather than selecting only by length or appearance.
Supply a mating-interface drawing and the required connector family, protocol support, active or passive design and retention. Add quantity, destination and any inspection requirements. Changes must be reviewed for the selected construction before compatibility, pricing or delivery can be confirmed.
Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.
We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details