Control cabinets
Terminal Block Adapters can be evaluated for control cabinets. Match wire range, pitch, mounting, jumper system and electrical ratings to the equipment interface.
Explore products in this family. Open a product for details, or send us your drawing for a custom build.
| Part number | Description |
|---|---|
| 106161001 | SKH D32 LP 5/16 |
| 2280307 | INTERFACE MODULE 15POS PNL MNT |
| ELC201100 | CONN TERM BLK CARD EDGE 20POS |
| 2299770 | FRONT ADAPTER 16 CHANNELS |
| ELC182100 | CONN TERM BLK CARD EDGE 18POS |
| FIT0852 | RJ45 TERMINAL BLOCK ADAPTER - HO |
| 1915712 | TERM BLOCK PLUG 8POS STR 3.5MM |
| 2280349 | INTERFACE MODULE 37POS PNL MNT |
| MF40MD-I | 40 TERM CONN W/40 PIN HEADER |
| 2280310 | INTERFACE MODULE 25POS PNL MNT |
| 2302463 | ROUND SHIELDED CABLE SET 15POS |
| 2280323 | INTERFACE MODULE 25POS PNL MNT |
| 2280268 | INTERFACE MODULE 34POS PNL MNT |
| 2291286 | INTERFACE MODULE 50POS PNL MNT |
| 770-1701 | T-DISTRIBUTION CONNECTOR 2-POLE |
| ELI020100 | CONN TERM BLK CARD EDGE 2POS |
| 890-1665 | T-DISTRIBUTION CONNECTOR 2-POLE |
| 1793260 | TERM BLOCK PCB |
| 770-605 | INTERMEDIATE COUPLER 5-POLE COD. |
| 770-1606 | T-DISTRIBUTION CONNECTOR 2-POLE |
| KF2270500000G | 1000 TB PCB CONNECTOR |
| KF16A0500000G | 750 TB PCB CONNECTOR |
| 232-562/007-000 | DOUBLE PIN HEADER; DIN-35 RAIL M |
| KF2410500000G | 1450 TB PCB CONNECTOR |
The Terminal Block Adapters range covers wire connections organised in compatible terminal-block systems.
Compare wire range, pitch, mounting, jumper system and electrical ratings for the required installation. Check both adapter interfaces and the contact mapping. A connector-format change alone does not provide protocol or signal conversion.
Review wire range, pitch, mounting, jumper system and electrical ratings on the individual product page before choosing a part.
Potential uses vary by part number. Check the listed specifications and equipment requirements before selecting a product.
Terminal Block Adapters can be evaluated for control cabinets. Match wire range, pitch, mounting, jumper system and electrical ratings to the equipment interface.
For equipment wiring, verify wire range, pitch, mounting, jumper system and electrical ratings on the selected Terminal Block Adapters. Check both adapter interfaces and the contact mapping. A connector-format change alone does not provide protocol or signal conversion.
In interface assemblies, allow for the required mounting, routing or termination space. Check wire range, pitch, mounting, jumper system and electrical ratings before assembly.
For terminal block adapters inspection, identify the original Terminal Block Adapters part number and mating arrangement. Compare wire range, pitch, mounting, jumper system and electrical ratings before substitution.
Compare the interfaces, construction and selection details of these two product options.
Example: 1239.3
Example: 1233.3
The comparison describes common construction differences; final suitability depends on your electrical, mechanical and lifetime requirements.
Practical answers to help you prepare your drawing and specifications.
This category covers wire connections organised in compatible terminal-block systems. Check both adapter interfaces and the contact mapping. A connector-format change alone does not provide protocol or signal conversion.
Match the selected Terminal Block Adapters to the required wire range, pitch, mounting, jumper system and electrical ratings.
For Terminal Block Adapters, check wire range, pitch, mounting, jumper system and electrical ratings against the equipment or mating-part drawing. Confirm the installed clearance and termination access as well as the nominal interface size.
Check wire range, pitch, mounting, jumper system and electrical ratings for the selected part. Use its stated operating conditions and complete assembly requirements; appearance alone does not establish the electrical or environmental rating.
Check both adapter interfaces and the contact mapping. A connector-format change alone does not provide protocol or signal conversion. For Terminal Block Adapters, identify the matching system and required assembly parts before ordering.
1239.3 specifies the part drawing. 1233.3 specifies the part drawing. Check the full mating and installation requirements before treating different Terminal Block Adapters as replacements.
Send the manufacturer and full part number, quantity and required delivery destination. For this category, include wire range, pitch, mounting, jumper system and electrical ratings and a mating or installation drawing when a replacement is needed.
Send a drawing, a BOM, a part number or just one sentence. Our engineers review every enquiry and reply within 24 hours.
We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.more details